Mitsubishi Lancer Owners Manual

Changing the function settings (when the ignition switch is “ON”)
Instruments and controls / Multi-information display / Changing the function settings (when the ignition switch is “ON”)

1. Stop the vehicle in a safe place.

Firmly apply the parking brake and put the gearshift lever into the “N” (Neutral) position (M/T), the selector lever into the “P” (PARK) position (CVT) or the gearshift lever into the “P” (PARK) position (Twin Clutch SST).

2. Lightly press the multi-information meter switch a few times to switch the information screen to the function setting screen. Refer to “Information display (when the ignition switch is “ON”)”.

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”).

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). Caution Caution

► For safety, stop the vehicle before operating.
While driving, even if you operate the multi- information meter switch, the function setting screen is not displayed.

3. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). Note

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). ► To return the menu screen to the function setting screen, press and hold the Note

► To return the menu screen to the function setting screen, press and hold the multi-information meter switch for about 2 seconds or more.
► If no operations are made within about 15 seconds of the menu screen being displayed, the display returns to the function setting screen.

4. Select the item to change on the menu screen and change to the desired setting. Refer to the following items for further details on the operation methods.

Changing the reset mode for average fuel consumption and average speed

The mode conditions for the average fuel consumption and average speed display can be switched between “Auto reset” and “Manual reset”.

1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.

Refer to “Changing the function settings (when the ignition switch is “ON”)”.

2. Lightly press the multi-information meter switch to select “AVG (average fuel consumption and average speed setting)”.

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). 3. Press and hold the multi-information meter switch for about 2 seconds or more

3. Press and hold the multi-information meter switch for about 2 seconds or more to switch in sequence from A or 1 (Auto reset mode) → M, 2 or P (Manual reset mode) → A or 1 (Auto reset mode).

The setting is changed to the selected mode condition.

Manual reset mode

► When the average fuel consumption and average speed are being displayed, if you hold down the multi-information meter switch, the average fuel consumption and average speed displayed at that time are reset.
► When the ignition switch is switched from “ACC” or “LOCK” to “ON”, the mode setting is automatically switched from manual to auto.

Switching to auto occurs automatically. If switching to manual mode is done, however, the data from the last reset is displayed.

Auto reset mode

► When the average fuel consumption and average speed are being displayed, if you hold down the multi-information meter switch, the average fuel consumption and average speed displayed at that time are reset.
► If the ignition switch is at “ACC” or “LOCK” for about 4 hours or longer, the average fuel consumption display and average speed display are automatically reset.

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). ► The memory of the auto reset mode or manual reset mode for the average speed Note

► The memory of the auto reset mode or manual reset mode for the average speed display is erased if the battery is disconnected.
► The initial (default) setting is “Auto reset mode”.

Changing the fuel consumption display unit

The display unit for fuel consumption can be switched.

The distance, speed, and amount units are also switched to match the selected fuel consumption unit.

1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.

Refer to “Changing the function settings (when the ignition switch is “ON”)”.

2. Lightly press the multi-information meter switch to select “AVG UNIT (fuel consumption display setting)”.

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). 3. Press and hold the multi-information meter switch for about 2 seconds or more

3. Press and hold the multi-information meter switch for about 2 seconds or more to display “AVG UNIT” (fuel consumption display unit setting).

4. Lightly press the multi-information meter switch to switch in sequence from km/L → L/100 km → mpg (US) → mpg (UK) → RETURN → km/L.

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). 5. Press and hold the multi-information meter switch for about 2 seconds or more

5. Press and hold the multi-information meter switch for about 2 seconds or more to change the setting to the selected unit.

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). ► The display units for the driving range, the average fuel consumption, the Note

► The display units for the driving range, the average fuel consumption, the average speed and the momentary fuel consumption are switched, but the units for the indicating needle (speedometer), the odometer and the tripmeter will remain unchanged.
► The memory of the unit setting is erased if the battery is disconnected, and it returns automatically to L/100 km.

The distance and speed units are also switched in the following combinations to match the selected fuel consumption unit.

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). Changing the temperature unit

Changing the temperature unit

The display unit for temperature can be switched.

1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen. Refer to “Changing the function settings (when the ignition switch is “ON”)”.
2. Lightly press the multi-information meter switch to select Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). (temperature unit setting).

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). 3. Press and hold the multi-information meter switch for about 2 seconds or more

3. Press and hold the multi-information meter switch for about 2 seconds or more to switch in sequence from °C → °F → °C.

The setting is changed to the selected temperature unit.

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). ► If the battery is disconnected, the unit setting is erased from memory and Note

► If the battery is disconnected, the unit setting is erased from memory and is automatically set to °C.

Changing the display language

The language of the multi-information display can be switched.

1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.

Refer to “Changing the function settings (when the ignition switch is “ON”)”.

2. Lightly press the multi-information meter switch to select “LANGUAGE” (language setting).

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). 3. Press and hold the multi-information meter switch for about 2 seconds or more

3. Press and hold the multi-information meter switch for about 2 seconds or more to display “LANGUAGE” (language setting).
4. Lightly press the multi-information meter switch to select the desired language.
5. If you hold down the multi-information meter switch for about 2 seconds or more, the setting is changed to the selected language.

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). ► The memory of the language setting is erased if the battery is disconnected, Note

► The memory of the language setting is erased if the battery is disconnected, and it returns automatically to ENGLISH or RUSSIAN.
► If “---” is selected in the language setting, a warning message is not displayed when there is a warning display or interrupt display.

Changing the language cooperative control

The language used in MITSUBISHI Multi-Communication System (MMCS) (if so equipped) or the Bluetooth® 2.0 interface (if so equipped) can be changed automatically to the same language as that shown in the multi-information display.

1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.
Refer to “Changing the function settings (when the ignition switch is “ON”)”.
2. Lightly press the multi-information meter switch to select Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). (language cooperative control).

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). 3. Press and hold the multi-information meter switch to switch in sequence from

3. Press and hold the multi-information meter switch to switch in sequence from A or 1 (language cooperation enabled) → M, 2 or P (language cooperation disabled) → A or 1 (language cooperation enabled).

The setting is changed to the selected condition.

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). ► The memory of the language cooperative control is erased if the battery is Note

► The memory of the language cooperative control is erased if the battery is disconnected, and it returns automatically to A or 1 (language cooperation enabled).
► The language display modified with the language setting can be switched in the following manner.
• When A or 1 (language cooperation enabled) has been selected with the language cooperative control, the language for MITSUBISHI Multi-Communication System (MMCS) (if so equipped) or the Bluetooth® 2.0 interface (if so equipped) is automatically changed to the language selected for the multi-information display.
• When M, 2 or P (language cooperation disabled) has been selected with the language cooperative control, the language for MITSUBISHI Multi-Communication System (MMCS) (if so equipped) or the Bluetooth® 2.0 interface (if so equipped) is not automatically changed to the language selected for the multi-information display.

Operation sound setting

You can turn off the operation sounds of the multiinformation meter switch and daytime dipper button.

1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.

Refer to “Changing the function settings (when the ignition switch is “ON”)”.
2. Lightly press the multi-information meter switch to select Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). (operation sound setting).

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). 3. Press and hold the multi-information meter switch for about 2 seconds or more

3. Press and hold the multi-information meter switch for about 2 seconds or more to switch in sequence from ON (operation sound on) → OFF (operation sound off) → ON (operation sound on).

The setting is changed to the selected condition.

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). ► The memory of the operation sound setting is erased if the battery is disconnected, Note

► The memory of the operation sound setting is erased if the battery is disconnected, and it returns automatically to ON (operation sound on).
► The operation sound setting only deactivates the operation sound of the multi-information meter switch and daytime dipper button. The warning display and other sounds cannot be deactivated.

Changing the time until “REST REMINDER” is displayed

The time until the display appears can be changed.

1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.

Refer to “Changing the function settings (when the ignition switch is “ON”)”.

2. Lightly press the multi-information meter switch to select “ALARM” (rest time setting).

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). 3. Press and hold the multi-information meter switch for about 2 seconds or more

3. Press and hold the multi-information meter switch for about 2 seconds or more to display “ALARM” (rest time setting).

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). 4. Lightly press the multi-information meter switch to select the time until

4. Lightly press the multi-information meter switch to select the time until the display.
5. Press and hold the multi-information meter switch for about 2 seconds or more, the setting is changed to the selected time.

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). ► If the battery is disconnected, the unit setting is erased from memory and Note

► If the battery is disconnected, the unit setting is erased from memory and is automatically set to OFF.
► The drive time is reset when the ignition switch is turned off.

Changing the turn-signal sound

It is possible to change the turn-signal sound.

1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.

Refer to “Changing the function settings (when the ignition switch is “ON”)”.

2. Lightly press the multi-information meter switch to select Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). (changing the turn-signal sound).

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). 3. Press and hold the multi-information meter switch for about 2 seconds or more

3. Press and hold the multi-information meter switch for about 2 seconds or more to switch in sequence from 1 (turn-signal sound 1) → 2 (turn-signal sound 2) → 1 (turn-signal sound 1).

The setting changes to the selected turn-signal sound.

Changing the momentary fuel consumption display (Type 2)

It is possible to change the bar graph setting of the momentary fuel consumption display.

1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.

Refer to “Changing the function settings (when the ignition switch is “ON”)”.
2. Lightly press the multi-information meter switch to select Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). consumption display) (changing the momentary fuel consumption display)

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). 3. Press and hold the multi-information meter switch for about 2 seconds or more

3. Press and hold the multi-information meter switch for about 2 seconds or more to switch in sequence from ON (with the green bar graph) → OFF (without the green bar graph) → ON (with the green bar graph).

The setting changes to the selected bar graph setting.

Returning to the factory settings

All of the function settings can be returned to their factory settings.

1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.

Refer to “Changing the function settings (when the ignition switch is “ON”)”.
2. Lightly press the multi-information meter switch to select “RESET” (returning to the factory settings).

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). 3. When you press and hold the multi-information meter switch for about 5 seconds

3. When you press and hold the multi-information meter switch for about 5 seconds or more, the buzzer sounds and all of the function settings are returned to the factory settings.

Mitsubishi Lancer: Changing the function settings (when the ignition switch is “ON”). ► The factory settings are as follows. Note

► The factory settings are as follows.
• Average fuel consumption and average speed reset mode: A (Auto reset)
• Fuel consumption display unit: L/100 km
• Temperature unit: °C (Celsius)
• Display language: ENGLISH or RUSSIAN
• Cooperative language setting: A
• Operation sounds: ON (Operation sounds on)
• “REST REMINDER” display: OFF
• Turn-signal sound: Turn-signal sound 1
• Momentary fuel consumption with the green bar graph (Type 2): ON


© 2024 www.mitsuguide.com. All Rights Reserved.